/*
             LUFA Library
     Copyright (C) Dean Camera, 2013.

  dean [at] fourwalledcubicle [dot] com
           www.lufa-lib.org
*/

/*
  Copyright 2013  Dean Camera (dean [at] fourwalledcubicle [dot] com)

  Permission to use, copy, modify, distribute, and sell this
  software and its documentation for any purpose is hereby granted
  without fee, provided that the above copyright notice appear in
  all copies and that both that the copyright notice and this
  permission notice and warranty disclaimer appear in supporting
  documentation, and that the name of the author not be used in
  advertising or publicity pertaining to distribution of the
  software without specific, written prior permission.

  The author disclaims all warranties with regard to this
  software, including all implied warranties of merchantability
  and fitness.  In no event shall the author be liable for any
  special, indirect or consequential damages or any damages
  whatsoever resulting from loss of use, data or profits, whether
  in an action of contract, negligence or other tortious action,
  arising out of or in connection with the use or performance of
  this software.
*/

/** \file
 *  \brief USB Controller definitions for the AVR XMEGA microcontrollers.
 *  \copydetails Group_USBManagement_XMEGA
 *
 *  \note This file should not be included directly. It is automatically included as needed by the USB driver
 *        dispatch header located in LUFA/Drivers/USB/USB.h.
 */

/** \ingroup Group_USBManagement
 *  \defgroup Group_USBManagement_XMEGA USB Interface Management (XMEGA)
 *  \brief USB Controller definitions for the AVR XMEGA microcontrollers.
 *
 *  Functions, macros, variables, enums and types related to the setup and management of the USB interface.
 *
 *  @{
 */

#ifndef __USBCONTROLLER_XMEGA_H__
#define __USBCONTROLLER_XMEGA_H__

	/* Includes: */
		#include "../../../../Common/Common.h"
		#include "../USBMode.h"
		#include "../Events.h"
		#include "../USBTask.h"
		#include "../USBInterrupt.h"

	/* Private Interface - For use in library only: */
	#if !defined(__DOXYGEN__)
		/* Macros: */
			#if defined(MAX_ENDPOINT_INDEX)
				#define ENDPOINT_TABLE_COUNT  (MAX_ENDPOINT_INDEX + 1)
			#else
				#define ENDPOINT_TABLE_COUNT  16
			#endif

		/* Type Defines: */
			typedef struct
			{
				struct
				{
					USB_EP_t OUT;
					USB_EP_t IN;
				} Endpoints[ENDPOINT_TABLE_COUNT];
				uint16_t FrameNum;
			} ATTR_PACKED USB_EndpointTable_t;

		/* External Variables: */
			extern uint8_t USB_EndpointTable[];
	#endif

	/* Includes: */
		#if defined(USB_CAN_BE_DEVICE) || defined(__DOXYGEN__)
			#include "../Device.h"
			#include "../Endpoint.h"
			#include "../DeviceStandardReq.h"
			#include "../EndpointStream.h"
		#endif

	/* Enable C linkage for C++ Compilers: */
		#if defined(__cplusplus)
			extern "C" {
		#endif

	/* Preprocessor Checks and Defines: */
		#if !defined(__INCLUDE_FROM_USB_DRIVER)
			#error Do not include this file directly. Include LUFA/Drivers/USB/USB.h instead.
		#endif

		#if !defined(F_USB)
			#error F_USB is not defined. You must define F_USB to the frequency of the unprescaled USB controller clock in your project makefile.
		#endif

		#if ((F_USB % 6000000) || (F_USB < 6000000))
			#error Invalid F_USB specified. F_USB must be a multiple of 6MHz for USB Low Speed operation, and a multiple of 48MHz for Full Speed operation.
		#endif

	/* Public Interface - May be used in end-application: */
		/* Macros: */
			/** \name USB Controller Option Masks */
			//@{
			/** Sets the USB bus interrupt priority level to be low priority. The USB bus interrupt is used for Start of Frame events, bus suspend
			 *  and resume events, bus reset events and other events related to the management of the USB bus.
			 */
			#define USB_OPT_BUSEVENT_PRILOW           ((0 << 2) | (0 << 1))

			/** Sets the USB bus interrupt priority level to be medium priority. The USB bus interrupt is used for Start of Frame events, bus suspend
			 *  and resume events, bus reset events and other events related to the management of the USB bus.
			 */
			#define USB_OPT_BUSEVENT_PRIMED           ((0 << 2) | (1 << 1))

			/** Sets the USB bus interrupt priority level to be high priority. The USB bus interrupt is used for Start of Frame events, bus suspend
			 *  and resume events, bus reset events and other events related to the management of the USB bus.
			 */
			#define USB_OPT_BUSEVENT_PRIHIGH          ((1 << 2) | (0 << 1))

			/** Sets the USB controller to source its clock from the internal RC 32MHz clock, once it has been DFLL calibrated to 48MHz. */
			#define USB_OPT_RC32MCLKSRC               (0 << 3)

			/** Sets the USB controller to source its clock from the internal PLL. */
			#define USB_OPT_PLLCLKSRC                 (1 << 3)
			//@}

			#if !defined(USB_STREAM_TIMEOUT_MS) || defined(__DOXYGEN__)
				/** Constant for the maximum software timeout period of the USB data stream transfer functions
				 *  (both control and standard) when in either device or host mode. If the next packet of a stream
				 *  is not received or acknowledged within this time period, the stream function will fail.
				 *
				 *  This value may be overridden in the user project makefile as the value of the
				 *  \ref USB_STREAM_TIMEOUT_MS token, and passed to the compiler using the -D switch.
				 */
				#define USB_STREAM_TIMEOUT_MS       100
			#endif

		/* Inline Functions: */
			/** Detaches the device from the USB bus. This has the effect of removing the device from any
			 *  attached host, ceasing USB communications. If no host is present, this prevents any host from
			 *  enumerating the device once attached until \ref USB_Attach() is called.
			 */
			static inline void USB_Detach(void) ATTR_ALWAYS_INLINE;
			static inline void USB_Detach(void)
			{
				USB.CTRLB &= ~USB_ATTACH_bm;
			}

			/** Attaches the device to the USB bus. This announces the device's presence to any attached
			 *  USB host, starting the enumeration process. If no host is present, attaching the device
			 *  will allow for enumeration once a host is connected to the device.
			 *
			 *  This is inexplicably also required for proper operation while in host mode, to enable the
			 *  attachment of a device to the host. This is despite the bit being located in the device-mode
			 *  register and despite the datasheet making no mention of its requirement in host mode.
			 */
			static inline void USB_Attach(void) ATTR_ALWAYS_INLINE;
			static inline void USB_Attach(void)
			{
				USB.CTRLB |= USB_ATTACH_bm;
			}

		/* Function Prototypes: */
			/** Main function to initialize and start the USB interface. Once active, the USB interface will
			 *  allow for device connection to a host when in device mode, or for device enumeration while in
			 *  host mode.
			 *
			 *  As the USB library relies on interrupts for the device and host mode enumeration processes,
			 *  the user must enable global interrupts before or shortly after this function is called. In
			 *  device mode, interrupts must be enabled within 500ms of this function being called to ensure
			 *  that the host does not time out whilst enumerating the device. In host mode, interrupts may be
			 *  enabled at the application's leisure however enumeration will not begin of an attached device
			 *  until after this has occurred.
			 *
			 *  Calling this function when the USB interface is already initialized will cause a complete USB
			 *  interface reset and re-enumeration.
			 *
			 *  \param[in] Mode     Mask indicating what mode the USB interface is to be initialized to, a value
			 *                      from the \ref USB_Modes_t enum.
			 *                      \note This parameter does not exist on devices with only one supported USB
			 *                            mode (device or host).
			 *
			 *  \param[in] Options  Mask indicating the options which should be used when initializing the USB
			 *                      interface to control the USB interface's behavior. This should be comprised of
			 *                      a \c USB_OPT_REG_* mask to control the regulator, a \c USB_OPT_*_PLL mask to control the
			 *                      PLL, and a \c USB_DEVICE_OPT_* mask (when the device mode is enabled) to set the device
			 *                      mode speed.
			 *
			 *  \note To reduce the FLASH requirements of the library if only device or host mode is required,
			 *        the mode can be statically set in the project makefile by defining the token \c USB_DEVICE_ONLY
			 *        (for device mode) or \c USB_HOST_ONLY (for host mode), passing the token to the compiler
			 *        via the -D switch. If the mode is statically set, this parameter does not exist in the
			 *        function prototype.
			 *        \n\n
			 *
			 *  \note To reduce the FLASH requirements of the library if only fixed settings are required,
			 *        the options may be set statically in the same manner as the mode (see the Mode parameter of
			 *        this function). To statically set the USB options, pass in the \c USE_STATIC_OPTIONS token,
			 *        defined to the appropriate options masks. When the options are statically set, this
			 *        parameter does not exist in the function prototype.
			 *        \n\n
			 *
			 *  \note The mode parameter does not exist on devices where only one mode is possible, such as USB
			 *        AVR models which only implement the USB device mode in hardware.
			 *
			 *  \see \ref Group_Device for the \c USB_DEVICE_OPT_* masks.
			 */
			void USB_Init(
			               #if defined(USB_CAN_BE_BOTH) || defined(__DOXYGEN__)
			               const uint8_t Mode
			               #endif

			               #if (defined(USB_CAN_BE_BOTH) && !defined(USE_STATIC_OPTIONS)) || defined(__DOXYGEN__)
			               ,
			               #elif (!defined(USB_CAN_BE_BOTH) && defined(USE_STATIC_OPTIONS))
			               void
			               #endif

			               #if !defined(USE_STATIC_OPTIONS) || defined(__DOXYGEN__)
			               const uint8_t Options
			               #endif
			               );

			/** Shuts down the USB interface. This turns off the USB interface after deallocating all USB FIFO
			 *  memory, endpoints and pipes. When turned off, no USB functionality can be used until the interface
			 *  is restarted with the \ref USB_Init() function.
			 */
			void USB_Disable(void);

			/** Resets the interface, when already initialized. This will re-enumerate the device if already connected
			 *  to a host, or re-enumerate an already attached device when in host mode.
			 */
			void USB_ResetInterface(void);

		/* Global Variables: */
			#if defined(USB_CAN_BE_BOTH) || defined(__DOXYGEN__)
				/** Indicates the mode that the USB interface is currently initialized to, a value from the
				 *  \ref USB_Modes_t enum.
				 *
				 *  \attention This variable should be treated as read-only in the user application, and never manually
				 *             changed in value.
				 *
				 *  \note When the controller is initialized into UID auto-detection mode, this variable will hold the
				 *        currently selected USB mode (i.e. \ref USB_MODE_Device or \ref USB_MODE_Host). If the controller
				 *        is fixed into a specific mode (either through the \c USB_DEVICE_ONLY or \c USB_HOST_ONLY compile time
				 *        options, or a limitation of the USB controller in the chosen device model) this will evaluate to
				 *        a constant of the appropriate value and will never evaluate to \ref USB_MODE_None even when the
				 *        USB interface is not initialized.
				 */
				extern volatile uint8_t USB_CurrentMode;
			#elif defined(USB_CAN_BE_HOST)
				#define USB_CurrentMode USB_MODE_Host
			#elif defined(USB_CAN_BE_DEVICE)
				#define USB_CurrentMode USB_MODE_Device
			#endif

			#if !defined(USE_STATIC_OPTIONS) || defined(__DOXYGEN__)
				/** Indicates the current USB options that the USB interface was initialized with when \ref USB_Init()
				 *  was called. This value will be one of the \c USB_MODE_* masks defined elsewhere in this module.
				 *
				 *  \attention This variable should be treated as read-only in the user application, and never manually
				 *             changed in value.
				 */
				extern volatile uint8_t USB_Options;
			#elif defined(USE_STATIC_OPTIONS)
				#define USB_Options USE_STATIC_OPTIONS
			#endif

		/* Enums: */
			/** Enum for the possible USB controller modes, for initialization via \ref USB_Init() and indication back to the
			 *  user application via \ref USB_CurrentMode.
			 */
			enum USB_Modes_t
			{
				USB_MODE_None   = 0, /**< Indicates that the controller is currently not initialized in any specific USB mode. */
				USB_MODE_Device = 1, /**< Indicates that the controller is currently initialized in USB Device mode. */
			};

	/* Private Interface - For use in library only: */
	#if !defined(__DOXYGEN__)
		/* Function Prototypes: */
			#if defined(__INCLUDE_FROM_USB_CONTROLLER_C)
				static void USB_Init_Device(void);
			#endif

		/* Inline Functions: */
			static inline void USB_Controller_Enable(void) ATTR_ALWAYS_INLINE;
			static inline void USB_Controller_Enable(void)
			{
				USB.CTRLA |=  USB_ENABLE_bm;
			}

			static inline void USB_Controller_Disable(void) ATTR_ALWAYS_INLINE;
			static inline void USB_Controller_Disable(void)
			{
				USB.CTRLA &= ~USB_ENABLE_bm;
			}

			static inline void USB_Controller_Reset(void) ATTR_ALWAYS_INLINE;
			static inline void USB_Controller_Reset(void)
			{
				USB.CTRLA &= ~USB_ENABLE_bm;
				USB.CTRLA |=  USB_ENABLE_bm;
			}

	#endif

	/* Disable C linkage for C++ Compilers: */
		#if defined(__cplusplus)
			}
		#endif

#endif

/** @} */

